Modine PDP350AE0130 350,000 BTU Vertical Powered Vented Unit Heater - 115V

Modine PDP350AE0130 350,000 BTU Vertical Powered Vented Unit Heater - 115V - NG

Sku:

MODINE-PDP350AE0130

Out Stock,

Please Call (877) 847-0050 for Availability

$3,499.00

Featuring 82% thermal efficiency, the PDP350AE0130 has a 350,000 BTU input and 287,000 BTU output. The PDP series heaters use a collector box and power exhauster for maximum seasonal efficiency. Unit can be used vertically or horizontally and the exhaust can be rotated a full 180°. These units are designed to use the smallest diameter vent pipe possible and the intermittent pilot-ignition system features 100% shut-off and continuous retry.

This unit is certified for commercial and industrial use.

Single Stage Gas Valve: The main gas valve is factory installed. The main gas valve provides the pilot, regulator, main gas, and manual shutoff functions
Ignition controller: The intermittent pilot ignition controller has a 100% shut-off with continuous retry. The system will attempt to light the pilot for 70 seconds. If the pilot is not sensed for any reason, the ignition control will wait for approximately six minutes with the combination gas control closed and no spark. After six minutes, the cycle will begin again. After three cycles, some ignition controllers lockout for approximately one hour before the cycle begins again. This will continue indefinitely until the pilot flame is sensed or power is interrupted to the system
Time Delay Relay: Factory installed in electrical junction box. The time delay relay allows the gas controls to operate for approximately 30 to 90 seconds before the blower starts. This allows the heat exchanger a warm up period so that the initial delivered air is not cool. The time delay relay also keeps the motor running for approximately 30 - 90 seconds after the call for heat has been satisfied to remove the residual heat from the heat exchanger.
Low Voltage Terminal Board: The low voltage terminal board is located in electrical junction box. The terminal board is labeled to match the electrical wiring diagram provided with the unit
Control Step Down Transformer: Located in the electrical junction box. The transformer is used to step down the supply power (115V, 208V, 230V, 460V, 575V) to 24V for the gas controls, fan delay relay, field supplied motor starter, etc
High Limit Switch: The automatic reset high limit switch is factory installed on the side of the unit heater. If the limit temperature is exceeded, the gas controls are de-energized until the switch is cooled
Pressure Switch: A automatic reset vent pressure switch is supplied on all power vented unit heaters to prevent operation of the main burner in the event there is restricted venting of flue products. After the cause of the restriction has been corrected, the pressure switch will reset automatically
Power Exhauster: All power vented unit heaters are supplied with a round vent pipe connection. The power exhauster may be rotated 180° to allow for various venting directions

The PDP350AE0130 is for use with Natural Gas.

Product Overview
Tech Specs
Warranty Information
Manuals and Guides

Product Overview

This unit is certified for commercial and industrial use.

Single Stage Gas Valve: The main gas valve is factory installed. The main gas valve provides the pilot, regulator, main gas, and manual shutoff functions
Ignition controller: The intermittent pilot ignition controller has a 100% shut-off with continuous retry. The system will attempt to light the pilot for 70 seconds. If the pilot is not sensed for any reason, the ignition control will wait for approximately six minutes with the combination gas control closed and no spark. After six minutes, the cycle will begin again. After three cycles, some ignition controllers lockout for approximately one hour before the cycle begins again. This will continue indefinitely until the pilot flame is sensed or power is interrupted to the system
Time Delay Relay: Factory installed in electrical junction box. The time delay relay allows the gas controls to operate for approximately 30 to 90 seconds before the blower starts. This allows the heat exchanger a warm up period so that the initial delivered air is not cool. The time delay relay also keeps the motor running for approximately 30 - 90 seconds after the call for heat has been satisfied to remove the residual heat from the heat exchanger.
Low Voltage Terminal Board: The low voltage terminal board is located in electrical junction box. The terminal board is labeled to match the electrical wiring diagram provided with the unit
Control Step Down Transformer: Located in the electrical junction box. The transformer is used to step down the supply power (115V, 208V, 230V, 460V, 575V) to 24V for the gas controls, fan delay relay, field supplied motor starter, etc
High Limit Switch: The automatic reset high limit switch is factory installed on the side of the unit heater. If the limit temperature is exceeded, the gas controls are de-energized until the switch is cooled
Pressure Switch: A automatic reset vent pressure switch is supplied on all power vented unit heaters to prevent operation of the main burner in the event there is restricted venting of flue products. After the cause of the restriction has been corrected, the pressure switch will reset automatically
Power Exhauster: All power vented unit heaters are supplied with a round vent pipe connection. The power exhauster may be rotated 180° to allow for various venting directions

The PDP350AE0130 is for use with Natural Gas.

Tech Specs

General Features

Installation Type:

Ceiling Mount

Fuel Type:

Natural Gas (NG)

Certified Usage:

Commercial (Indoor Only)

Separated Combustion Chamber:

Performance

Heating BTUs (Input):

350000

Heating BTUs (Output):

290500

System Data

Noise Level (dBA):

Thermal Efficiency:

82%

CFMs:

4870

Output Velocity (FPMs):

1068

Discharge Air Temperature Rise (°F):

Discharge Air Opening Area (ft²):

Connections

Gas Connection Size:

3/4"

Vent Connection Size (in.):

Clearances

Top to Ceiling (in.):

Bottom to Floor (ft.):

To Side Wall (in.):

Access Panel (in.):

18"

Flue / Vent Connector (in.):

Weights and Dimensions

Width (in.):

33.625

Depth (in.):

Height (in.):

40.25

Net Weight (lbs.):

338

Electrical Requirements

Voltage:

110-120V

Amps:

11.15

Circuit Breaker Size (Amps):

Product Warranty

Heat Exchanger: 10 Years